Pleated Shades

Pleated Shades Across Bargersville, IN

One folded layer, priced honestly against a cellular shade.

Call (317) 854-7158Get Free Quote
Quick Answer

This section covers what the product does well, where it struggles, and what it costs to own over time rather than just to buy. All three matter on a purchase you'll live with for years.

  • Service: Pleated Shades for Bargersville homeowners
  • Service area: Bargersville, IN and surrounding areas
    • We book measures without much delay. What you can't compress is the fabrication window, which runs two to five weeks depending on the product and the finish. Painted shutter finishes sit at the longer end.
  • Insured and bonded
  • Serving Bargersville, IN since 2008
Pleated Shades Services

Expert Pleated Shades for Bargersville Homes

A pleated shade is a single folded fabric on a lift, without the sealed pocket a cellular carries, and it's the right answer when a room wants light control and nothing more expensive than that. Bargersville's older stock is where it turns up. The town added 610 units between 1940 and 1979, mostly scattered rural and county road housing rather than platted subdivisions, plus another 466 across the 1980s and 1990s. Those are smaller houses with smaller openings, built through decades when Bargersville barely grew, and they're a different proposition from the 2,000 to 3,400 square foot two story that dominates the town now.

The tradeoff is energy, and it's worth stating plainly. A cellular folds into closed cells that trap still air against the glass, and DOE and ORNL testing credited that construction with saving up to 20 percent of heating energy and up to 15 percent of total heating and cooling energy against a bare window. A pleated shade has no pocket at all, because it's one layer folded flat. In climate zone 5A, where January averages a 20.9 degree low against a 36.1 degree high, that difference is real on a north wall. Pleated fabric also shows its lift cord holes as a row of pinpricks when the light is behind it.

When to Call

Signs You Need Pleated Shades

If you notice any of these in your Bargersville home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

Cellular quotes came back higher than the room needs

Water was used to clean pleats and they relaxed

A house is going on the market and looks unfinished

A bonus room over the garage bakes in the afternoon

Trim is too shallow for a deeper headrail

Temporary paper shades have been up for two years

A laundry sink window has warped a wood blind

The cord lock has to be reset every single morning

A spare bedroom still has nothing on the window

A rental turns over and every window is bare

Our Process

How Bargersville Window Treatments Handles Pleated Shades

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

Three widths, three heights, diagonal

2

Mounting depth read

3

Full travel run twice per unit

4

Room sorted by what it actually needs

5

Specialty shapes templated on site

Real Project Photos

Pleated Shades in Bargersville

Photographs from real pleated shades jobs completed by our crew in Bargersville and surrounding areas.

Custom shades measured and installed in BargersvillePlantation shutters fitted to a Bargersville windowCellular shades in a Bargersville living room
Scope of Work

What Pleated Shades Includes

Every Bargersville job is documented item by item. Here is what the crew covers.

The energy question answered honestly up front: a pleated shade is one layer of fabric with no cell behind it

Rooms steered to cellular instead wherever trapped air is the actual reason for the purchase

Rooms where pleated is the right call identified plainly, from secondary bedrooms to offices to a rental turnover

Pleat size set against the opening, a fine pleat on short glass and a larger pleat where the drop can carry it

Fabric opacity settled in writing before the order, light filtering against room darkening

Reflective backing considered on hard west and south exposures, described as what it is rather than as an energy rating

Three widths and three heights per opening with a diagonal check for square

Mounting depth read so the headrail sits inside the opening where an inside mount is what you want

Stack at the top measured against the glass, since a stacked pleated shade still covers the top few inches

Cordless lift specified in rooms children use, with products conforming to ANSI/WCMA A100.1-2022 for cord access

Route holes disclosed on any corded unit, because a closed pleated shade shows those holes as a line of small bright dots

Light gap per side written onto the paperwork, along with the 1/16 inch per side factory deduction Lutron publishes

Top-down bottom-up priced where a room wants daylight high and cover low

Arched, angled and fan-shaped openings templated on site, since pleated fabric is what those get built from

Wide spans reviewed for headrail deflection and split into two units where that is the right answer

Every opening in a room ordered on one purchase so the fabric comes off the same run

The paperwork done properly, with IC 24-5-11 requiring scope, dates and total price on residential jobs over $150

Bottom rail leveled and full travel run twice at every unit before we pack up

Pricing

What Pleated Shades Cost in Bargersville

National category figures put stock shades near $60 to $600 a window and custom-fabricated shades roughly $250 to $2,600. Those are published national ranges, not a price for any opening in Bargersville. Pleated sits low in the custom band and that is the honest appeal of it. One layer of fabric, a light headrail and a simple lift add up to less than a double cell shade with a blackout fabric and two lift systems. Where the number climbs is the same place it climbs on everything: width, drop, a room darkening fabric, a cordless lift on a heavy unit, or a templated arch that somebody has to build to a pattern. Bargersville Window Treatments prices from measured openings across Johnson County rather than from a per-window average.

By Product

How Pleated Shades Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

1 inch pleat: The standard and the one most rooms get. It holds a crisp horizontal line at ordinary window heights, it stacks small at the top, and it keeps the scale right on the bedroom and office windows this product usually goes into.

Fine pleat: A smaller fold for short windows, transoms and specialty shapes. More folds across the same drop means a finer face, and it's what a small arch or a narrow sidelight needs so the shape doesn't look coarse.

2 inch pleat: A larger fold that suits tall glass and big rooms, where a fine pleat across a long drop starts to read as texture rather than as a line. Fewer folds also means a slightly smaller stack for the same height.

Light filtering fabric: The everyday specification. Diffused daylight comes through, the view does not, and the room stays bright. It's the fabric that suits an office, a stairwell or any bedroom where waking up with the sun isn't a problem.

Room darkening fabric: A denser fabric that cuts most light through the face. It gets a bedroom dim rather than dark, since a pleated shade doesn't seal at the edges and an inside mount still passes light down both sides.

Reflective backing: A metallized back face that bounces some of the sun striking the shade back at the glass. It's a real property of the fabric and it's not an energy rating, and we describe it that way rather than putting a number on it.

Cordless spring lift: A spring lift with no operating cord on the product, and the version we specify in any room a child uses. It also removes the route holes from the conversation, since there's no lift cord passing through the fabric.

Corded lift with a cord lock: The traditional and least expensive control. The lift cord runs through holes punched in the pleats, which is exactly where a closed shade shows a vertical line of small bright dots at night. Worth knowing before you save the money.

Top-down bottom-up: Two rails on one shade, so the top can drop for daylight while the bottom stays up against a sidewalk. It adds a second lift system and its own hardware, which is where much of the extra cost comes from.

Fixed arch and angle-top units: A half-round, a quarter-round or an angled top built to a site template and left fixed. Pleated fabric is what these get made from, because a pleated fan holds its shape where a rolling product simply can't follow the geometry.

Light Control

See What Each Fabric Does To The Light

Pick a fabric below and the window updates. It's a drawing rather than a photograph, so read it as a rough guide to what each family does in a Bargersville room, and to what it doesn't do.

Fabric type

Sheer, 10 percent openness

Ten percent of the weave is open, so you keep the view and most of the daylight. Glare drops a little. After dark, once your lamps are on, someone outside can read shapes through it, which is why this belongs on a view window rather than a bedroom.

Openness factor is printed on the fabric card, so you can compare one line against another before you order anything.

Keeps the viewNot private after dark

Solar, 5 percent openness

The usual pick for a west window or a covered porch. You can still read the yard through it, glare comes down noticeably, and the fabric intercepts a good share of the sun before it reaches you at four in the afternoon.

It also cuts the UV landing on floors and furniture. NFRC puts UV at roughly 40 to 60 percent of fading damage, so this slows fading rather than stopping it.

View and glare controlSlows fading

Solar, 3 percent openness

A tighter weave. The room goes dimmer and the view drops back to an outline. Choose it where the sun is the problem and the view is second, which around here usually means a west wall in July. That's a common call on this side of Indianapolis.

Openness affects how much you see out, not how private you are. A 3 percent fabric still shows silhouettes at night.

View becomes an outlineStrong glare control

Solar, 1 percent openness

Close to a solid fabric with a little view left in it. This is the strongest glare control in the solar family.

The trade is that it darkens the room on a gray January day too. Indianapolis averages a January high near 36F and the light is flat, so think about how the room reads in both seasons before you commit.

Darkest solar optionDim on gray days

Light filtering

No view through it. Daylight comes through the face diffused, so the room stays bright without a hot spot across the television or the kitchen island. This is the default for living spaces.

It isn't private in reverse at night. With the lamps on and the sun down, silhouettes still show.

No view through itBright without the glare

Room darkening

A denser fabric, usually with a liner behind it. Most of the light coming through the face is gone.

Light still arrives around the edges on an inside mount, so a room darkening shade gives you a dim room rather than a dark one. If someone in the house sleeps during the day, say so at the measure and we'll scope it differently.

Dim, not darkEdges stay bright

Blackout

The fabric itself passes essentially no light. What you'll still see is the perimeter. Lutron publishes an inside-mount light gap of about 3/4 inch per side on its Roller 20 and 64 shades, along with a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps than that.

So if you need a genuinely dark bedroom, that gap has to be dealt with on purpose, either with side channels or by going outside mount. We tell you which one your opening can carry while we're still standing in the room.

Dark facePerimeter needs a plan

Openness factor is a measured fabric spec, so you can compare it line to line. The category names are not measured. One maker's room darkening can behave like another maker's light filtering, which is why the sample books come to the measure and get opened in the room they're going in, at the hour that room has the problem.

Common Questions

Pleated Shades FAQ

Questions we hear most often from Bargersville homeowners considering pleated shades.

Cellular, if the budget reaches. The 314 Bargersville units built between 1970 and 1979 are mostly scattered county road housing rather than platted subdivision stock, and those houses take weather on all four elevations with no neighbors close enough to break the wind. That's exactly where the trapped air in a cellular does the most work through a January averaging a 20.9 degree low. Pleated is the honest choice for a spare bedroom, a hallway, or an opening you simply want covered. We don't pretend a pleated shade performs like a cellular, and anybody who tells you it does is selling.
Because the lift cord has to pass through the fabric. On a standard pleated shade the cords run through punched holes in each fold, and with the sun behind the shade those holes read as a vertical line of pinpricks down the face. It's normal and it's permanent. Cordless construction removes the exterior cord but not always the internal routing, so ask specifically. If those pinpoints will bother you in a room you sit in every evening, that's a reason to spend up to a cellular, where the cord runs inside the cell rather than through the visible face. On a Bargersville west opening the sun sits behind the shade most afternoons.
Less, and the gap is smaller than people expect once the shade is custom sized. National figures put stock shades and blinds at roughly $60 to $600 per window and custom work at roughly $250 to $2,600 per window. Those are national ranges and not Bargersville quotes, because no installed pricing is published for this market. Within custom work, pleated sits at the lower end and cellular above it, and in a house carrying 18 to 26 openings the difference multiplies. Indiana's Home Improvement Contract Act, IC 24-5-11, means residential work above $150 gets a written contract carrying the scope and the total price.
Reasonably, with a caveat about heat. Pleated fabric is heat set at the factory, and the fold memory holds well in normal use. What softens it is sustained direct sun on the same fold line year after year, and Bargersville gives it plenty, since roughly 63.7 percent of the housing here sits on former farmland with street trees only 5 to 25 years old. A shade left down all summer on a west opening loses crispness faster than one that gets raised. The lift mechanism usually needs attention before the fabric does, and both are serviceable rather than disposable.
It can, and the reason is privacy rather than light. Bradford Place is 90 parcels on a 0.20 acre median, the tightest lots of any Bargersville plat sampled, so the side bedroom windows along Pineleigh Place and Oakton Way look straight at the neighboring wall from close range. Those openings need covering more than they need performance, since the neighboring house is already blocking most of the sun. A pleated shade in a room darkening fabric handles that at a sensible price. On the front and rear elevations of the same house we'd specify differently.
Yes, and in a house with children that's where we start. A cordless pleated shade runs on an internal lift and a spring in the headrail, so there's no exterior cord to reach. An inner cord that falls short of the requirement counts as a substantial product hazard under 16 CFR 1120.3, and the standard behind current goods is ANSI/WCMA A100.1-2022. The tradeoff is that the spring loses tension across years of daily use, so an old cordless shade can creep down or need a firmer push to stay at the top. That's a serviceable part, not the end of the shade.
Structure. A pleated shade is a single layer of fabric folded into pleats, so when you look at the edge you see one accordion. A cellular shade is two layers joined so the folds form closed cells, and when you look at the edge you see honeycombs with air inside them. That trapped air is the entire point of a cellular shade. A pleated shade doesn't have it, which is why it costs less and why we don't make an energy argument for it.
Not the way a cellular does, and we won't pretend otherwise. Any fabric between you and cold glass in a Bargersville January does something, since it slows the air movement at the window and takes the edge off a draft you can feel from the couch. What it doesn't have is the trapped air pocket. The DOE and ORNL testing that gets quoted in this trade, up to 20 percent heating energy savings and up to 15 percent of total heating and cooling energy, was done on cellular shades. If that number is why you're buying, buy cellular.
When the room needs a good-looking shade rather than an energy product. Secondary bedrooms, home offices, hallways, a bonus room over a garage, a rental between tenants, a house being prepared for sale. All of those want something that fits the opening properly and costs sensibly. Pleated does that. It's also the right answer on arched and angled openings where no other product follows the shape, and that has nothing to do with budget.
Mostly, and they do soften. A pleated shade holds its folds because the fabric was heat-set at the factory, and that set relaxes slowly, faster on a hot window than on a shaded one. After several years on a west-facing Bargersville window you may see the folds sit slightly less sharp than they did, particularly at the bottom of the shade where it spends most of its life stacked. A cellular shade holds its shape longer because the cells brace each other. That's a real difference worth knowing.
Because the lift cord runs through holes punched in the fabric. On a corded pleated shade, each pleat has a small hole for the cord to pass through, and with the shade down those holes stack into a vertical line of bright dots that you notice at night and barely see during the day. It's construction, not damage. Cordless lift removes them entirely, since there's no cord passing through the fabric, and that's one of the better reasons to spend the difference.
In any room a child or a pet uses, yes, and we specify it that way. There's no operating cord on the product at all, which is the direction the ANSI/WCMA A100.1-2022 work on cord access points, and inner-cord non-compliance is treated as a substantial product hazard under 16 CFR 1120.3. On a pleated shade there's a second benefit, which is the route holes disappearing. The tradeoff is cost and the fact that a wide unit wants a hand at each end of the bottom rail rather than one in the middle.
Dim, not dark, and the reason is the edges rather than the fabric. A room darkening pleated fabric blocks most of the light through its face. What it can't do is close the gap down each side of an inside mount, and Lutron publishes 3/4 inch per side as a real inside-mount figure on their roller product to give you a sense of the scale. For a genuinely dark bedroom the answer is an outside mount with real overlap, or a blackout fabric running in side channels, which is a different product.
Yes, and pleated is usually what those get built from. A half-round over a front door, a quarter-round in a stairwell, an angled top following a vaulted ceiling: all of them get a site template, and the shade is fabricated as a fixed fan to that pattern. Fixed means it doesn't operate, which surprises people, so we say it early. If the shape has to move, the honest answer is often a movable shade below the straight line and a fixed unit above it.
Less than most products, and not nothing. A raised pleated shade gathers into a compact stack at the headrail, smaller than a double cell shade of the same height and much smaller than a woven natural. On a tall window that stack is a couple of inches of glass. On a short window it's a bigger share of the view, which is why we measure the drop and tell you where the bottom rail will actually sit when the shade is fully up.
Dust them and leave them alone otherwise. A vacuum on low with a brush head across the face, or a soft duster run along the folds, handles routine dirt. Spot marks come off with a barely damp cloth blotted, never rubbed hard, because the fabric is thin and the heat-set folds don't like being worked. Don't submerge them, and don't use a steamer on them. Fabric that has been soaked tends to come back with soft folds that never recover their line.
Reasonably, with the usual honesty about the exposure. A west or south window in Johnson County takes real sun from late May into September, and a light colored pleated fabric there will soften in color over the years more than the same fabric on a north window. A reflective backing helps the fabric itself and improves how the shade looks from the street, since all the shades read the same color from outside. On the room behind it, NFRC puts UV at roughly 40 to 60 percent of fading damage, so the shade slows what happens to your floors. It doesn't end it.
Wide enough for most rooms, with weight and headrail deflection as the limits. Pleated fabric is light, so the fabric itself isn't the constraint. What matters is the headrail across a long span and the way a wide bottom rail behaves when you lift it from one end. Past the point where a single unit gets awkward, two shades sharing an opening reads better than one that drags. We work that out at the measure rather than after the box arrives.
Close, and possibly not exact. Pleated fabrics run in dye lots, so a shade woven this year can sit slightly off one woven three years ago. Across a hallway nobody sees it. On two windows in the same wall everybody does. The practical advice is to do a room in one order, even the small window you were going to skip. We write the fabric name and color onto your paperwork so a later order at least starts from the right reference.
Two to five weeks is the normal custom fabrication window, and pleated usually sits at the shorter end because it's a simple build. Templated arches and angle tops run longer, since somebody is making a one-off to your pattern. The window goes into your paperwork along with the scope, the dates and the total price, which the Indiana Home Improvement Contract Act requires on residential work over $150.
Areas We Serve

Pleated Shades Across Bargersville

We measure and install in every one of these Bargersville neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in Bargersville

Bargersville Window Treatments handles the full scope of window treatment work. Explore our other services below.

Faux Wood Blinds in Bargersville

PVC slats where Bargersville humidity would ruin real wood.

Learn more →

Wood Blinds in Bargersville

Real hardwood where Bargersville air stays dry and steady.

Learn more →

Vertical Blinds in Bargersville

Patio door coverage sized to Bargersville's post-2000 rear elevations.

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in Bargersville

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
Bargersville, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 854-7158
Service area

Serving Bargersville and the surrounding area

Call NowGet Quote